Tag Archives: YouTubers

Safety first: a Raspberry Pi safety helmet

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/safety-helmet/

Jennifer Fox is back, this time with a Raspberry Pi Zero–controlled impact force monitor that will notify you if your collision is a worth a trip to the doctor.

Make an Impact Force Monitor!

Check out my latest Hacker in Residence project for SparkFun Electronics: the Helmet Guardian! It’s a Pi Zero powered impact force monitor that turns on an LED if your head/body experiences a potentially dangerous impact. Install in your sports helmets, bicycle, or car to keep track of impact and inform you when it’s time to visit the doctor.

Concussion

We’ve all knocked our heads at least once in our lives, maybe due to tripping over a loose paving slab, or to falling off a bike, or to walking into the corner of the overhead cupboard door for the third time this week — will I ever learn?! More often than not, even when we’re seeing stars, we brush off the accident and continue with our day, oblivious to the long-term damage we may be doing.

Force of impact

After some thorough research, Jennifer Fox, founder of FoxBot Industries, concluded that forces of 4 to 6 G sustained for more than a few seconds are dangerous to the human body. With this in mind, she decided to use a Raspberry Pi Zero W and an accelerometer to create helmet with an impact force monitor that notifies its wearer if this level of G-force has been met.

Jennifer Fox Raspberry Pi Impact Force Monitor

Obviously, if you do have a serious fall, you should always seek medical advice. This project is an example of how affordable technology can be used to create medical and citizen science builds, and not a replacement for professional medical services.

Setting up the impact monitor

Jennifer’s monitor requires only a few pieces of tech: a Zero W, an accelerometer and breakout board, a rechargeable USB battery, and an LED, plus the standard wires and resistors for these components.

After installing Raspbian, Jennifer enabled SSH and I2C on the Zero W to make it run headlessly, and then accessed it from a laptop. This allows her to control the Pi without physically connecting to it, and it makes for a wireless finished project.

Jen wired the Pi to the accelerometer breakout board and LED as shown in the schematic below.

Jennifer Fox Raspberry Pi Impact Force Monitor

The LED acts as a signal of significant impacts, turning on when the G-force threshold is reached, and not turning off again until the program is reset.

Jennifer Fox Raspberry Pi Impact Force Monitor

Make your own and more

Jennifer’s full code for the impact monitor is on GitHub, and she’s put together a complete tutorial on SparkFun’s website.

For more tutorials from Jennifer Fox, such as her ‘Bark Back’ IoT Pet Monitor, be sure to follow her on YouTube. And for similar projects, check out Matt’s smart bike light and Amelia Day’s physical therapy soccer ball.

The post Safety first: a Raspberry Pi safety helmet appeared first on Raspberry Pi.

Tinkernut’s hidden Coke bottle spy cam

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/tinkernuts-spy-cam/

Go undercover and keep an eye on your stuff with this brilliant secret Coke bottle spy cam from Tinkernut!

Secret Coke Bottle SPY CAM! – Weekend Hacker #1803

SPECIAL NOTE*** THE FULL TUTORIAL WILL BE AVAILABLE NEXT WEEK April Fools! What a terrible day. So many pranks. You can’t believe anything you read. People invading your space. The mental and physical anguish of enduring the day. It’s time to fight back! Let’s catch the perps in action by making a device that always watches.

Keeping tabs

A Raspberry Pi Zero W, a small camera, and a rechargeable Lithium Polymer (LiPo) battery constitute the bulk of this project’s tech. A pair of 3D-printed parts, and gelatine-solidified Coke Zero make up the fake fizzy body.

Tinkernut Coke bottle Raspberry Pi Spy Cam

“So let’s make this video as short as possible and just buy a cheap pre-made spy cam off of Amazon. Just kidding,” Tinkernut jokes in the tutorial video for the project, before going through the step-by-step process of using the Raspberry Pi to “DIY this the right way”.

After accessing the Zero W from his laptop via SSH, Tinkernut opted for using the rpi_camera_surveillance_system Python script written by GitHub user RuiSantosdotme to control the spy cam. Luckily, this meant no additional library setup, and basically no lag on the video feed.

What we want to do is create a script that activates the camera and serves it to a web page so that we can access it from any web browser. There are plenty of different ways to do this (Motion, Raspivid, etc), but I found a simple Python script that does everything I need it to do and doesn’t require any extra software or libraries to install. The best thing about it is that the lag time is practically unnoticeable.

With the code in place, every boot-up of the Raspberry Pi automatically launches both the script and a web page of the live video, allowing for constant monitoring of potential sneaks and thieves.

Tinkernut Coke bottle Raspberry Pi Spy Cam

The projects is powered by a 1500mAh LiPo battery and the Adafruit LiPo charger. It also includes a simple on/off switch, which Tinkernut wired to the charger and the Pi’s PP1 and PP6 connector pads.

Tinkernut Coke bottle Raspberry Pi Spy Cam

Tinkernut decided to use a Coke Zero bottle for the build, incorporating 3D-printed parts to house the Pi, and a mix of Coke and gelatine to create a realistic-looking filling for the bottle. However, the setup can be transferred to pretty much any hollow item in your home, say, a cookie jar or a cracker box. So get creative and get spying!

A complete spy cam how-to

If you’d like to make your own secret spy cam, you can find a tutorial for Tinkernut’s build at hackster.io, or follow along with his video below. Also make sure to subscribe his YouTube channel to be updated on all his newest builds — they’re rather splendid.

BUILD: Coke Bottle SPY CAM! – Tinkernut Workbench

Learn how to take a regular Coke Zero bottle, cram a Raspberry Pi and webcam inside of it, and have it still look like a regular Coke Zero bottle. Why would you want to do this? To spy on those irritating April Fooligans!!!

And if you’re interested in more spy-themed digital making projects, check out our complete 007 how-to guide for links to tutorials such as our Sense HAT puzzle box, Parent detector, and Laser tripwire.

The post Tinkernut’s hidden Coke bottle spy cam appeared first on Raspberry Pi.

Pi 3B+: 48 hours later

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/3b-plus-aftermath/

Unless you’ve been AFK for the last two days, you’ll no doubt be aware of the release of the brand-spanking-new Raspberry Pi 3 Model B+. With faster connectivity, more computing power, Power over Ethernet (PoE) pins, and the same $35 price point, the new board has been a hit across all our social media accounts! So while we wind down from launch week, let’s all pull up a chair, make yet another cup of coffee, and look through some of our favourite reactions from the last 48 hours.

Twitter

Our Twitter mentions were refreshing at hyperspeed on Wednesday, as you all began to hear the news and spread the word about the newest member to the Raspberry Pi family.

Tanya Fish on Twitter

Happy Pi Day, people! New @Raspberry_Pi 3B+ is out.

News outlets, maker sites, and hobbyists published posts and articles about the new Pi’s spec upgrades and their plans for the device.

Hackster.io on Twitter

This sort of attention to detail work is exactly what I love about being involved with @Raspberry_Pi. We’re squeezing the last drops of performance out of the 40nm process node, and perfecting Pi 3 in the same way that the original B+ perfected Pi 1.” https://t.co/hEj7JZOGeZ

And I think we counted about 150 uses of this GIF on Twitter alone:

YouTube

Andy Warburton 👾 on Twitter

Is something going on with the @Raspberry_Pi today? You’d never guess from my YouTube subscriptions page… 😀

A few members of our community were lucky enough to get their hands on a 3B+ early, and sat eagerly by the YouTube publish button, waiting to release their impressions of our new board to the world. Others, with no new Pi in hand yet, posted reaction vids to the launch, discussing their plans for the upgraded Pi and comparing statistics against its predecessors.

New Raspberry Pi 3 B+ (2018) Review and Speed Tests

Happy Pi Day World! There is a new Raspberry Pi 3, the B+! In this video I will review the new Pi 3 B+ and do some speed tests. Let me know in the comments if you are getting one and what you are planning on making with it!

Long-standing community members such as The Raspberry Pi Guy, Alex “RasPi.TV” Eames, and Michael Horne joined Adafruit, element14, and RS Components (whose team produced the most epic 3B+ video we’ve seen so far), and makers Tinkernut and Estefannie Explains It All in sharing their thoughts, performance tests, and baked goods on the big day.

What’s new on the Raspberry Pi 3 B+

It’s Pi day! Sorry, wondrous Mathematical constant, this day is no longer about you. The Raspberry Pi foundation just released a new version of the Raspberry Pi called the Rapsberry Pi B+.

If you have a YouTube or Vimeo channel, or if you create videos for other social media channels, and have published your impressions of the new Raspberry Pi, be sure to share a link with us so we can see what you think!

Instagram

We shared a few photos and videos on Instagram, and over 30000 of you checked out our Instagram Story on the day.

Some glamour shots of the latest member of the #RaspberryPi family – the Raspberry Pi 3 Model B+ . Will you be getting one? What are your plans for our newest Pi?

5,609 Likes, 103 Comments – Raspberry Pi (@raspberrypifoundation) on Instagram: “Some glamour shots of the latest member of the #RaspberryPi family – the Raspberry Pi 3 Model B+ ….”

As hot off the press (out of the oven? out of the solder bath?) Pi 3B+ boards start to make their way to eager makers’ homes, they are all broadcasting their excitement, and we love seeing what they plan to get up to with it.

The new #raspberrypi 3B+ suits the industrial setting. Check out my website for #RPI3B Vs RPI3BPlus network speed test. #NotEnoughTECH #network #test #internet

8 Likes, 1 Comments – Mat (@notenoughtech) on Instagram: “The new #raspberrypi 3B+ suits the industrial setting. Check out my website for #RPI3B Vs RPI3BPlus…”

The new Raspberry Pi 3 Model B+ is here and will be used for our Python staging server for our APIs #raspberrypi #pythoncode #googleadwords #shopify #datalayer

16 Likes, 3 Comments – Rob Edlin (@niddocks) on Instagram: “The new Raspberry Pi 3 Model B+ is here and will be used for our Python staging server for our APIs…”

In the news

Eben made an appearance on ITV Anglia on Wednesday, talking live on Facebook about the new Raspberry Pi.

ITV Anglia

As the latest version of the Raspberry Pi computer is launched in Cambridge, Dr Eben Upton talks about the inspiration of Professor Stephen Hawking and his legacy to science. Add your questions in…

He was also fortunate enough to spend the morning with some Sixth Form students from the local area.

Sascha Williams on Twitter

On a day where science is making the headlines, lovely to see the scientists of the future in our office – getting tips from fab @Raspberry_Pi founder @EbenUpton #scientists #RaspberryPi #PiDay2018 @sirissac6thform

Principal Hardware Engineer Roger Thornton will also make a live appearance online this week: he is co-hosting Hack Chat later today. And of course, you can see more of Roger and Eben in the video where they discuss the new 3B+.

Introducing the Raspberry Pi 3 Model B+

Raspberry Pi 3 Model B+ is now on sale now for $35.

It’s been a supremely busy week here at Pi Towers and across the globe in the offices of our Approved Resellers, and seeing your wonderful comments and sharing in your excitement has made it all worth it. Please keep it up, and be sure to share the arrival of your 3B+ as well as the projects into which you’ll be integrating them.

If you’d like to order a Raspberry Pi 3 Model B+, you can do so via our product page. And if you have any questions at all regarding the 3B+, the conversation is still taking place in the comments of Wednesday’s launch post, so head on over.

The post Pi 3B+: 48 hours later appeared first on Raspberry Pi.

Community Profile: Estefannie Explains It All

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/community-profile-estefannie/

This column is from The MagPi issue 59. You can download a PDF of the full issue for free, or subscribe to receive the print edition through your letterbox or the digital edition on your tablet. All proceeds from the print and digital editions help the Raspberry Pi Foundation achieve our charitable goals.

“Hey, world!” Estefannie exclaims, a wide grin across her face as the camera begins to roll for another YouTube tutorial video. With a growing number of followers and wonderful support from her fans, Estefannie is building a solid reputation as an online maker, creating unique, fun content accessible to all.

A woman sitting at a desk with a laptop and papers — Estefannie Explains it All Raspberry Pi

It’s as if she was born into performing and making for an audience, but this fun, enjoyable journey to social media stardom came not from a desire to be in front of the camera, but rather as a unique approach to her own learning. While studying, Estefannie decided the best way to confirm her knowledge of a subject was to create an educational video explaining it. If she could teach a topic successfully, she knew she’d retained the information. And so her YouTube channel, Estefannie Explains It All, came into being.

Note taking — Estefannie Explains it All

Her first videos featured pages of notes with voice-over explanations of data structure and algorithm analysis. Then she moved in front of the camera, and expanded her skills in the process.

But YouTube isn’t her only outlet. With nearly 50000 followers, Estefannie’s Instagram game is strong, adding to an increasing number of female coders taking to the platform. Across her Instagram grid, you’ll find insights into her daily routine, from programming on location for work to behind-the-scenes troubleshooting as she begins to create another tutorial video. It’s hard work, with content creation for both Instagram and YouTube forever on her mind as she continues to work and progress successfully as a software engineer.

A woman showing off a game on a tablet — Estefannie Explains it All Raspberry Pi

As a thank you to her Instagram fans for helping her reach 10000 followers, Estefannie created a free game for Android and iOS called Gravitris — imagine Tetris with balance issues!

Estefannie was born and raised in Mexico, with ambitions to become a graphic designer and animator. However, a documentary on coding at Pixar, and the beauty of Merida’s hair in Brave, opened her mind to the opportunities of software engineering in animation. She altered her career path, moved to the United States, and switched to a Computer Science course.

A woman wearing safety goggles hugging a keyboard Estefannie Explains it All Raspberry Pi

With a constant desire to make and to learn, Estefannie combines her software engineering profession with her hobby to create fun, exciting content for YouTube.

While studying, Estefannie started a Computer Science Girls Club at the University of Houston, Texas, and she found herself eager to put more time and effort into the movement to increase the percentage of women in the industry. The club was a success, and still is to this day. While Estefannie has handed over the reins, she’s still very involved in the cause.

Through her YouTube videos, Estefannie continues the theme of inclusion, with every project offering a warm sense of approachability for all, regardless of age, gender, or skill. From exploring Scratch and Makey Makey with her young niece and nephew to creating her own Disney ‘Made with Magic’ backpack for a trip to Disney World, Florida, Estefannie’s videos are essentially a documentary of her own learning process, produced so viewers can learn with her — and learn from her mistakes — to create their own tech wonders.

Using the Raspberry Pi, she’s been able to broaden her skills and, in turn, her projects, creating a home-automated gingerbread house at Christmas, building a GPS-controlled GoPro for her trip to London, and making everyone’s life better with an Internet Button–controlled French press.

Estefannie Explains it All Raspberry Pi Home Automated Gingerbread House

Estefannie’s automated gingerbread house project was a labour of love, with electronics, wires, and candy strewn across both her living room and kitchen for weeks before completion. While she already was a skilled programmer, the world of physical digital making was still fairly new for Estefannie. Having ditched her hot glue gun in favour of a soldering iron in a previous video, she continued to experiment and try out new, interesting techniques that are now second nature to many members of the maker community. With the gingerbread house, Estefannie was able to research and apply techniques such as light controls, servos, and app making, although the latter was already firmly within her skill set. The result? A fun video of ups and downs that resulted in a wonderful, festive treat. She even gave her holiday home its own solar panel!

A DAY AT RASPBERRY PI TOWERS!! LINK IN BIO ⚡🎥 @raspberrypifoundation

1,910 Likes, 43 Comments – Estefannie Explains It All (@estefanniegg) on Instagram: “A DAY AT RASPBERRY PI TOWERS!! LINK IN BIO ⚡🎥 @raspberrypifoundation”

And that’s just the beginning of her adventures with Pi…but we won’t spoil her future plans by telling you what’s coming next. Sorry! However, since this article was written last year, Estefannie has released a few more Pi-based project videos, plus some awesome interviews and live-streams with other members of the maker community such as Simone Giertz. She even made us an awesome video for our Raspberry Pi YouTube channel! So be sure to check out her latest releases.

Best day yet!! I got to hangout, play Jenga with a huge arm robot, and have afternoon tea with @simonegiertz and robots!! 🤖👯 #shittyrobotnation

2,264 Likes, 56 Comments – Estefannie Explains It All (@estefanniegg) on Instagram: “Best day yet!! I got to hangout, play Jenga with a huge arm robot, and have afternoon tea with…”

While many wonderful maker videos show off a project without much explanation, or expect a certain level of skill from viewers hoping to recreate the project, Estefannie’s videos exist almost within their own category. We can’t wait to see where Estefannie Explains It All goes next!

The post Community Profile: Estefannie Explains It All appeared first on Raspberry Pi.

N-O-D-E’s always-on networked Pi Plug

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/node-pi-plug/

N-O-D-E’s Pi Plug is a simple approach to using a Raspberry Pi Zero W as an always-on networked device without a tangle of wires.

Pi Plug 2: Turn The Pi Zero Into A Mini Server

Today I’m back with an update on the Pi Plug I made a while back. This prototype is still in the works, and is much more modular than the previous version. https://N-O-D-E.net/piplug2.html https://github.com/N-O-D-E/piplug —————- Shop: http://N-O-D-E.net/shop/ Patreon: http://patreon.com/N_O_D_E_ BTC: 17HqC7ZzmpE7E8Liuyb5WRbpwswBUgKRGZ Newsletter: http://eepurl.com/ceA-nL Music: https://archive.org/details/Fwawn-FromManToGod

The Pi Zero Power Case

In a video early last year, YouTuber N-O-D-E revealed his Pi Zero Power Case, an all-in-one always-on networked computer that fits snugly against a wall power socket.

NODE Plug Raspberry Pi Plug

The project uses an official Raspberry Pi power supply, a Zero4U USB hub, and a Raspberry Pi Zero W, and it allows completely wireless connection to a network. N-O-D-E cut the power cord and soldered its wires directly to the power input of the USB hub. The hub powers the Zero via pogo pins that connect directly to the test pads beneath.

The Power Case is a neat project, but it may be a little daunting for anyone not keen on cutting and soldering the power supply wires.

Pi Plug 2

In his overhaul of the design, N-O-D-E has created a modular reimagining of the previous always-on networked computer that fits more streamlined to the wall socket and requires absolutely no soldering or hacking of physical hardware.

Pi Plug

The Pi Plug 2 uses a USB power supply alongside two custom PCBs and a Zero W. While one PCB houses a USB connector that slots directly into the power supply, two blobs of solder on the second PCB press against the test pads beneath the Zero W. When connected, the PCBs run power directly from the wall socket to the Raspberry Pi Zero W. Neat!

NODE Plug Raspberry Pi
NODE Plug Raspberry Pi
NODE Plug Raspberry Pi
NODE Plug Raspberry Pi

While N-O-D-E isn’t currently selling these PCBs in his online store, all files are available on GitHub, so have a look if you want to recreate the Pi Plug.

Uses

In another video — and seriously, if you haven’t checked out N-O-D-E’s YouTube channel yet, you really should — he demonstrates a few changes that can turn your Zero into a USB dongle computer. This is a great hack if you don’t want to carry a power supply around in your pocket. As N-O-D-E explains:

Besides simply SSH’ing into the Pi, you could also easily install a remote desktop client and use the GUI. You can share your computer’s internet connection with the Pi and use it just like you would normally, but now without the need for a monitor, chargers, adapters, cables, or peripherals.

We’re keen to see how our community is hacking their Zeros and Zero Ws in order to take full advantage of the small footprint of the computer, so be sure to share your projects and ideas with us, either in the comments below or via social media.

The post N-O-D-E’s always-on networked Pi Plug appeared first on Raspberry Pi.

Hacker House’s Zero W–powered automated gardener

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/hacker-house-automated-gardener/

Are the plants in your home or office looking somewhat neglected? Then build an automated gardener using a Raspberry Pi Zero W, with help from the team at Hacker House.

Make a Raspberry Pi Automated Gardener

See how we built it, including our materials, code, and supplemental instructions, on Hackster.io: https://www.hackster.io/hackerhouse/automated-indoor-gardener-a90907 With how busy our lives are, it’s sometimes easy to forget to pay a little attention to your thirsty indoor plants until it’s too late and you are left with a crusty pile of yellow carcasses.

Building an automated gardener

Tired of their plants looking a little too ‘crispy’, Hacker House have created an automated gardener using a Raspberry Pi Zero W alongside some 3D-printed parts, a 5v USB grow light, and a peristaltic pump.

Hacker House Automated Gardener Raspberry Pi

They designed and 3D printed a PLA casing for the project, allowing enough space within for the Raspberry Pi Zero W, the pump, and the added electronics including soldered wiring and two N-channel power MOSFETs. The MOSFETs serve to switch the light and the pump on and off.

Hacker House Automated Gardener Raspberry Pi

Due to the amount of power the light and pump need, the team replaced the Pi’s standard micro USB power supply with a 12v switching supply.

Coding an automated gardener

All the code for the project — a fairly basic Python script —is on the Hacker House GitHub repository. To fit it to your requirements, you may need to edit a few lines of the code, and Hacker House provides information on how to do this. You can also find more details of the build on the hackster.io project page.

Hacker House Automated Gardener Raspberry Pi

While the project runs with preset timings, there’s no reason why you couldn’t upgrade it to be app-based, for example to set a watering schedule when you’re away on holiday.

To see more for the Hacker House team, be sure to follow them on YouTube. You can also check out some of their previous Raspberry Pi projects featured on our blog, such as the smartphone-connected door lock and gesture-controlled holographic visualiser.

Raspberry Pi and your home garden

Raspberry Pis make great babysitters for your favourite plants, both inside and outside your home. Here at Pi Towers, we have Bert, our Slack- and Twitter-connected potted plant who reminds us when he’s thirsty and in need of water.

Bert Plant on Twitter

I’m good. There’s plenty to drink!

And outside of the office, we’ve seen plenty of your vegetation-focused projects using Raspberry Pi for planting, monitoring or, well, commenting on social and political events within the media.

If you use a Raspberry Pi within your home gardening projects, we’d love to see how you’ve done it. So be sure to share a link with us either in the comments below, or via our social media channels.

 

The post Hacker House’s Zero W–powered automated gardener appeared first on Raspberry Pi.

Build a Binary Clock with engineerish

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/engineerish-binary-clock/

Standard clocks with easily recognisable numbers are so last season. Who wants to save valuable seconds simply telling the time, when a series of LEDs and numerical notation can turn every time query into an adventure in mathematics?

Build a Binary Clock with Raspberry Pi – And how to tell the time

In this video I’ll be showing how I built a binary clock using a Raspberry Pi, NeoPixels and a few lines of Python. I also take a stab at explaining how the binary number system works so that we can decipher what said clock is trying to tell us.

How to read binary

I’ll be honest: I have to think pretty hard to read binary. It stretches my brain quite vigorously. But I am a fan of flashy lights and pretty builds, so YouTube and Instagram rising star Mattias Jähnke, aka engineerish, had my full attention from the off.

“If you have a problem with your friends being able to tell the time way too easily while in your house, this is your answer.”

Mattias offers a beginners’ guide in to binary in his video and then explains how his clock displays values in binary, before moving on to the actual clock build process. So make some tea, pull up a chair, and jump right in.

Binary clock

To build the clock, Mattias used a Raspberry Pi and NeoPixel strips, fitted snugly within a simple 3D-printed case. With a few lines of Python, he coded his clock to display the current time using the binary system, with columns for seconds, minutes, and hours.

The real kicker with a binary clock is that by the time you’ve deciphered what time it is – you’re probably already late.

418 Likes, 14 Comments – Mattias (@engineerish) on Instagram: “The real kicker with a binary clock is that by the time you’ve deciphered what time it is – you’re…”

The Python code isn’t currently available on Mattias’s GitHub account, but if you’re keen to see how he did it, and you ask politely, and he’s not too busy, you never know.

Make your own

In the meantime, while we batter our eyelashes in the general direction of Stockholm and hope for a response, I challenge any one of you to code a binary display project for the Raspberry Pi. It doesn’t have to be a clock. And it doesn’t have to use NeoPixels. Maybe it could use an LED matrix such as the SenseHat, or a series of independently controlled LEDs on a breadboard. Maybe there’s something to be done with servo motors that flip discs with different-coloured sides to display a binary number.

Whatever you decide to build, the standard reward applies: ten imaginary house points (of absolutely no practical use, but immense emotional value) and a great sense of achievement to all who give it a go.

The post Build a Binary Clock with engineerish appeared first on Raspberry Pi.

Playing tic-tac-toe against a Raspberry Pi at Maker Faire

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/tic-tac-toe-maker-faire/

At Maker Faire New York, we met up with student Toby Goebeler of Dover High School, Pennsylvania, to learn more about his Tic-Tac-Toe Robot.

Play Tic-Tac-Toe against a Raspberry Pi #MFNYC

Uploaded by Raspberry Pi on 2017-12-18.

Tic-tac-toe with Dover Robotics

We came to see Toby and Brian Bahn, physics teacher for Dover High School and leader of the Dover Robotics club, so they could tell us about the inner workings of the Tic-Tac-Toe Robot project, and how the Raspberry Pi fit within it. Check out our video for Toby’s explanation of the build and the software controlling it.

Wooden robotic arm — Toby Goebeler Tic-Tac-Toe arm Raspberry Pi

Toby’s original robotic arm prototype used a weight to direct the pen on and off the paper. He later replaced this with a servo motor.

Toby documented the prototyping process for the robot on the Dover Robotics blog. Head over there to hear more about the highs and lows of building a robotic arm from scratch, and about how Toby learned to integrate a Raspberry Pi for both software and hardware control.

Wooden robotic arm playing tic-tac-toe — Toby Goebeler Tic-Tac-Toe arm Raspberry Pi

The finished build is a tic-tac-toe beast, besting everyone who dares to challenge it to a game.

And in case you’re wondering: no, none of the Raspberry Pi team were able to beat the Tic-Tac-Toe Robot when we played against it.

Your turn

We always love seeing Raspberry Pis being used in schools to teach coding and digital making, whether in the classroom or during after-school activities such as the Dover Robotics club and our own Code Clubs and CoderDojos. If you are part of a coding or robotics club, we’d love to hear your story! So make sure to share your experiences and projects in the comments below, or via our social media accounts.

The post Playing tic-tac-toe against a Raspberry Pi at Maker Faire appeared first on Raspberry Pi.

Sean Hodgins’ video-playing Christmas ornament

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/sean-hodgins-ornament/

Standard Christmas tree ornaments are just so boring, always hanging there doing nothing. Yawn! Lucky for us, Sean Hodgins has created an ornament that plays classic nineties Christmas adverts, because of nostalgia.

YouTube Christmas Ornament! – Raspberry Pi Project

This Christmas ornament will really take you back…

Ingredients

Sean first 3D printed a small CRT-shaped ornament resembling the family television set in The Simpsons. He then got to work on the rest of the components.

Pi Zero and electronic components — Sean Hodgins Raspberry Pi Christmas ornament

All images featured in this blog post are c/o Sean Hodgins. Thanks, Sean!

The ornament uses a Raspberry Pi Zero W, 2.2″ TFT LCD screen, Mono Amp, LiPo battery, and speaker, plus the usual peripherals. Sean purposely assembled it with jumper wires and tape, so that he can reuse the components for another project after the festive season.

Clip of PowerBoost 1000 LiPo charger — Sean Hodgins Raspberry Pi Christmas ornament

By adding header pins to a PowerBoost 1000 LiPo charger, Sean was able to connect a switch to control the Pi’s power usage. This method is handy if you want to seal your Pi in a casing that blocks access to the power leads. From there, jumper wires connect the audio amplifier, LCD screen, and PowerBoost to the Zero W.

Code

Then, with Raspbian installed to an SD card and SSH enabled on the Zero W, Sean got the screen to work. The type of screen he used has both SPI and FBTFT enabled. And his next step was to set up the audio functionality with the help of an Adafruit tutorial.

Clip demoing Sean Hodgins Raspberry Pi Christmas ornament

For video playback, Sean installed mplayer before writing a program to extract video content from YouTube*. Once extracted, the video files are saved to the Raspberry Pi, allowing for seamless playback on the screen.

Construct

When fully assembled, the entire build fit snugly within the 3D-printed television set. And as a final touch, Sean added the cut-out lens of a rectangular magnifying glass to give the display the look of a curved CRT screen.

Clip of completed Sean Hodgins Raspberry Pi Christmas ornament in a tree

Then finally, the ornament hangs perfectly on the Christmas tree, up and running and spreading nostalgic warmth.

For more information on the build, check out the Instructables tutorial. And to see all of Sean’s builds, subscribe to his YouTube channel.

Make

If you’re looking for similar projects, have a look at this tutorial by Cabe Atwell for building a Pi-powered ornament that receives and displays text messages.

Have you created Raspberry Pi tree ornaments? Maybe you’ve 3D printed some of our own? We’d love to see what you’re doing with a Raspberry Pi this festive season, so make sure to share your projects with us, either in the comments below or via our social media channels.

 

*At this point, I should note that we don’t support the extraction of  video content from YouTube for your own use if you do not have the right permissions. However, since Sean’s device can play back any video, we think it would look great on your tree showing your own family videos from previous years. So, y’know, be good, be legal, and be festive.

The post Sean Hodgins’ video-playing Christmas ornament appeared first on Raspberry Pi.

Community Profile: Matthew Timmons-Brown

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/community-profile-matthew-timmons-brown/

This column is from The MagPi issue 57. You can download a PDF of the full issue for free, or subscribe to receive the print edition in your mailbox or the digital edition on your tablet. All proceeds from the print and digital editions help the Raspberry Pi Foundation achieve its charitable goals.

“I first set up my YouTube channel because I noticed a massive lack of video tutorials for the Raspberry Pi,” explains Matthew Timmons-Brown, known to many as The Raspberry Pi Guy. At 18 years old, the Cambridge-based student has more than 60 000 subscribers to his channel, making his account the most successful Raspberry Pi–specific YouTube account to date.

Matthew Timmons-Brown

Matt gives a talk at the Raspberry Pi 5th Birthday weekend event

The Raspberry Pi Guy

If you’ve attended a Raspberry Pi event, there’s a good chance you’ve already met Matt. And if not, you’ll have no doubt come across one or more of his tutorials and builds online. On more than one occasion, his work has featured on the Raspberry Pi blog, with his yearly Raspberry Pi roundup videos being a staple of the birthday celebrations.

Matthew Timmons-Brown

With his website, Matt aimed to collect together “the many strands of The Raspberry Pi Guy” into one, neat, cohesive resource — and it works. From newcomers to the credit card-sized computer to hardened Pi veterans, The Raspberry Pi Guy offers aid and inspiration for many. Looking for a review of the Raspberry Pi Zero W? He’s filmed one. Looking for a step-by-step guide to building a Pi-powered Amazon Alexa? No problem, there’s one of those too.

Make your Raspberry Pi artificially intelligent! – Amazon Alexa Personal Assistant Tutorial

Artificial Intelligence. A hefty topic that has dominated the field since computers were first conceived. What if I told you that you could put an artificial intelligence service on your own $30 computer?! That’s right! In this tutorial I will show you how to create your own artificially intelligent personal assistant, using Amazon’s Alexa voice recognition and information service!

Raspberry Pi electric skateboard

Last summer, Matt introduced the world to his Raspberry Pi-controlled electric skateboard, soon finding himself plastered over local press as well as the BBC and tech sites like Adafruit and geek.com. And there’s no question as to why the build was so popular. With YouTubers such as Casey Neistat increasing the demand for electric skateboards on a near-daily basis, the call for a cheaper, home-brew version has quickly grown.

DIY 30KM/H ELECTRIC SKATEBOARD – RASPBERRY PI/WIIMOTE POWERED

Over the summer, I made my own electric skateboard using a £4 Raspberry Pi Zero. Controlled with a Nintendo Wiimote, capable of going 30km/h, and with a range of over 10km, this project has been pretty darn fun. In this video, you see me racing around Cambridge and I explain the ins and outs of this project.

Using a Raspberry Pi Zero, a Nintendo Wii Remote, and a little help from members of the Cambridge Makespace community, Matt built a board capable of reaching 30km/h, with a battery range of 10km per charge. Alongside Neistat, Matt attributes the project inspiration to Australian student Tim Maier, whose build we previously covered in The MagPi.

Matthew Timmons-Brown and Eben Upton standing in a car park looking at a smartphone

LiDAR

Despite the success and the fun of the electric skateboard (including convincing Raspberry Pi Trading CEO Eben Upton to have a go for local television news coverage), the project Matt is most proud of is his wireless LiDAR system for theoretical use on the Mars rovers.

Matthew Timmons-Brown's LiDAR project for scanning terrains with lasers

Using a tablet app to define the angles, Matt’s A Level coursework LiDAR build scans the surrounding area, returning the results to the touchscreen, where they can be manipulated by the user. With his passion for the cosmos and the International Space Station, it’s no wonder that this is Matt’s proudest build.

Built for his A Level Computer Science coursework, the build demonstrates Matt’s passion for space and physics. Used as a means of surveying terrain, LiDAR uses laser light to measure distance, allowing users to create 3D-scanned, high-resolution maps of a specific area. It is a perfect technology for exploring unknown worlds.

Matthew Timmons-Brown and two other young people at a reception in the Houses of Parliament

Matt was invited to St James’s Palace and the Houses of Parliament as part of the Raspberry Pi community celebrations in 2016

Joining the community

In a recent interview at Hills Road Sixth Form College, where he is studying mathematics, further mathematics, physics, and computer science, Matt revealed where his love of electronics and computer science started. “I originally became interested in computer science in 2012, when I read a tiny magazine article about a computer that I would be able to buy with pocket money. This was a pretty exciting thing for a 12-year-old! Your own computer… for less than £30?!” He went on to explain how it became his mission to learn all he could on the subject and how, months later, his YouTube channel came to life, cementing him firmly into the Raspberry Pi community

The post Community Profile: Matthew Timmons-Brown appeared first on Raspberry Pi.

Hacker House’s gesture-controlled holographic visualiser

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/hacker-house-holographic-visualiser/

YouTube makers Hacker House are back with a beautiful Flick-controlled holographic music visualiser that we’d really like to have at Pi Towers, please and thank you.

Make a Holographic Audio Visualizer with Gesture Control

Find all the code and materials on: https://www.hackster.io/hackerhouse/holographic-audio-visualizer-with-motion-control-e72fee A 3D holographic audio visualizer with gesture control can definitely spice up your party and impress your friends. This display projects an image from a monitor down onto an acrylic pyramid, or “frustum”, which then creates a 3D effect.

Homemade holographic visualiser

You may have seen a similar trick for creating holograms in this tutorial by American Hacker:

How To Make 3D Hologram Projector – No Glasses

Who will know that from plastic cd case we can make mini 3d hologram generator and you can watch 3d videos without glasses.

The illusion works due to the way in which images reflect off a flat-topped pyramid or frustum, to use its proper name. In the wonderful way they always do, the residents of Hacker House have now taken this trick one step further.

The Hacker House upgrade

Using an LCD monitor, 3D-printed parts, a Raspberry Pi, and a Flick board, the Hacker House team has produced a music visualiser truly worthy of being on display.

Hacker House Raspberry Pi holographic visualiser

The Pi Supply Flick is a 3D-tracking and gesture board for your Raspberry Pi, enabling you to channel your inner Jedi and control devices with a mere swish of your hand. As the Hacker House makers explain, in this music player project, there are various ways in which you could control the playlist, visualisation, and volume. However, using the Flick adds a wow-factor that we highly approve of.

The music and visualisations are supplied by a Mac running node.js. As the Raspberry Pi is running on the same network as the Mac, it can communicate with the it via HTTP requests.

Sketch of network for Hacker House Raspberry Pi holographic visualiser

The Pi processes incoming commands from the Flick board, and in response send requests to the Mac. Swipe upward above the Flick board, for example, and the Raspberry Pi will request a change of visualisation. Swipe right, and the song will change.

Hacker House Raspberry Pi holographic visualiser

As for the hologram itself, it is formed on an acrylic pyramid sitting below an LCD screen. Images on the screen reflect off the three sides of the pyramid, creating the illusion of a three-dimensional image within. Standard hocus pocus trickery.

Full details on the holographic visualiser, including the scripts, can be found on the hackster.io project page. And if you make your own, we’d love to see it.

Your turn

Using ideas from this Hacker House build and the American Hacker tutorial, our maker community is bound to create amazing things with the Raspberry Pi, holograms, and tricks of the eye. We’re intrigued to see what you come up with!

For inspiration, another example of a Raspberry Pi optical illusion project is Brian Corteil’s Digital Zoetrope:

Brian Corteil's Digital Zoetrope - Hacker House Raspberry Pi holographic visualiser

Are you up for the challenge of incorporating optical illusions into your Raspberry Pi builds? Share your project ideas and creations in the comments below!

The post Hacker House’s gesture-controlled holographic visualiser appeared first on Raspberry Pi.

N O D E’s Handheld Linux Terminal

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/n-o-d-es-handheld-linux-terminal/

Fit an entire Raspberry Pi-based laptop into your pocket with N O D E’s latest Handheld Linux Terminal build.

The Handheld Linux Terminal Version 3 (Portable Pi 3)

Hey everyone. Today I want to show you the new version 3 of the Handheld Linux Terminal. It’s taken a long time, but I’m finally finished. This one takes all the things I’ve learned so far, and improves on many of the features from the previous iterations.

N O D E

With interests in modding tech, exploring the boundaries of the digital world, and open source, YouTuber N O D E has become one to watch within the digital maker world. He maintains a channel focused on “the transformative power of technology.”

“Understanding that electronics isn’t voodoo is really powerful”, he explains in his Patreon video. “And learning how to build your own stuff opens up so many possibilities.”

NODE Youtube channel logo - Handheld Linux Terminal v3

The topics of his videos range from stripped-down devices, upgraded tech, and security upgrades, to the philosophy behind technology. He also provides weekly roundups of, and discussions about, new releases.

Essentially, if you like technology, you’ll like N O D E.

Handheld Linux Terminal v3

Subscribers to N O D E’s YouTube channel, of whom there are currently over 44000, will have seen him documenting variations of this handheld build throughout the last year. By stripping down a Raspberry Pi 3, and incorporating a Zero W, he’s been able to create interesting projects while always putting functionality first.

Handheld Linux Terminal v3

With the third version of his terminal, N O D E has taken experiences gained from previous builds to create something of which he’s obviously extremely proud. And so he should be. The v3 handheld is impressively small considering he managed to incorporate a fully functional keyboard with mouse, a 3.5″ screen, and a fan within the 3D-printed body.

Handheld Linux Terminal v3

“The software side of things is where it really shines though, and the Pi 3 is more than capable of performing most non-intensive tasks,” N O D E goes on to explain. He demonstrates various applications running on Raspbian, plus other operating systems he has pre-loaded onto additional SD cards:

“I have also installed Exagear Desktop, which allows it to run x86 apps too, and this works great. I have x86 apps such as Sublime Text and Spotify running without any problems, and it’s technically possible to use Wine to also run Windows apps on the device.”

We think this is an incredibly neat build, and we can’t wait to see where N O D E takes it next!

The post N O D E’s Handheld Linux Terminal appeared first on Raspberry Pi.

Sean Hodgins’ Haunted Jack in the Box

Post Syndicated from Janina Ander original https://www.raspberrypi.org/blog/sean-hodgins-haunted-jack-box/

After making a delightful Bitcoin lottery using a Raspberry Pi, Sean Hodgins brings us more Pi-powered goodness in time for every maker’s favourite holiday: Easter! Just kidding, it’s Halloween. Check out his hair-raising new build, the Haunted Jack in the Box.

Haunted Jack in the Box – DIY Raspberry Pi Project

This project uses a raspberry pi and face detection using the pi camera to determine when someone is looking at it. Plenty of opportunities to scare people with it. You can make your own!

Haunted jack-in-the-box?

Imagine yourself wandering around a dimly lit house. Your eyes idly scan a shelf. Suddenly, out of nowhere, a twangy melody! What was that? You take a closer look…there seems to be a box in jolly colours…with a handle that’s spinning by itself?!

Sidling up to Sean Hodgins' Haunted Jack in the Box

What’s…going on?

You freeze, unable to peel your eyes away, and BAM!, out pops a maniacally grinning clown. You promptly pee yourself. Happy Halloween, courtesy of Sean Hodgins.

Clip of Sean Hodgins' Haunted Jack in the Box

Eerie disembodied voice: You’re welco-o-o-ome!

How has Sean built this?

Sean purchased a jack-in-the-box toy and replaced its bottom side with one that would hold the necessary electronic components. He 3D-printed this part, but says you could also just build it by hand.

The bottom of the box houses a Raspberry Pi 3 Model B and a servomotor which can turn the windup handle. There’s also a magnetic reed switch which helps the Pi decide when to trigger the Jack. Sean hooked up the components to the Pi’s GPIO pins, and used an elastic band as a drive belt to connect the pulleys on the motor and the handle.

Film clip showing the inside of Sean Hodgin's Haunted Jack in the Box

Sean explains that he has used a lot of double-sided tape and superglue in this build. The bottom and top are held together with two screws, because, as he describes it, “the Jack coming out is a little violent.”

In addition to his video walk-through, he provides build instructions on Instructables, Hackaday, Hackster, and Imgur — pick your poison. And be sure to subscribe to Sean’s YouTube channel to see what he comes up with next.

Wait, how does the haunted part work?

But if I explain it, it won’t be scary anymore! OK, fiiiine.

With the help of a a Camera Module and OpenCV, Sean implemented facial recognition: Jack knows when someone is looking at his box, and responds by winding up and popping out.

View of command line output of the Python script for Sean Hodgins' Haunted Jack in the Box

Testing the haunting script

Sean’s Python script is available here, but as he points out, there are many ways in which you could adapt this code, and the build itself, to be even more frightening.

So very haunted

What would you do with this build? Add creepy laughter? Soundbites from It? Lighting effects? Maybe even infrared light and a NoIR Camera Module, so that you can scare people in total darkness? There are so many possibilities for this project — tell us your idea in the comments.

The post Sean Hodgins’ Haunted Jack in the Box appeared first on Raspberry Pi.

Laser Cookies: a YouTube collaboration

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/laser-cookies/

Lasers! Cookies! Raspberry Pi! We’re buzzing with excitement about sharing our latest YouTube video with you, which comes directly from the kitchen of maker Estefannie Explains It All!

Laser-guarded cookies feat. Estefannie Explains It All

Uploaded by Raspberry Pi on 2017-09-18.

Estefannie Explains It All + Raspberry Pi

When Estefannie visited Pi Towers earlier this year, we introduced her to the Raspberry Pi Digital Curriculum and the free resources on our website. We’d already chatted to her via email about the idea of creating a collab video for the Raspberry Pi channel. Once she’d met members of the Raspberry Pi Foundation team and listened to them wax lyrical about the work we do here, she was even more keen to collaborate with us.

Estefannie on Twitter

Ahhhh!!! I still can’t believe I got to hang out and make stuff at the @Raspberry_Pi towers!! Thank you thank you!!

Estefannie returned to the US filled with inspiration for a video for our channel, and we’re so pleased with how awesome her final result is. The video is a super addition to our Raspberry Pi YouTube channel, it shows what our resources can help you achieve, and it’s great fun. You might also have noticed that the project fits in perfectly with this season’s Pioneers challenge. A win all around!

So yeah, we’re really chuffed about this video, and we hope you all like it too!

Estefannie’s Laser Cookies guide

For those of you wanting to try your hand at building your own Cookie Jar Laser Surveillance Security System, Estefannie has provided a complete guide to talk you through it. Here she goes:

First off, you’ll need:

  • 10 lasers
  • 10 photoresistors
  • 10 capacitors
  • 1 Raspberry Pi Zero W
  • 1 buzzer
  • 1 Raspberry Pi Camera Module
  • 12 ft PVC pipes + 4 corners
  • 1 acrylic panel
  • 1 battery pack
  • 8 zip ties
  • tons of cookies

I used the Raspberry Pi Foundation’s Laser trip wire and the Tweeting Babbage resources to get one laser working and to set up the camera and Twitter API. This took me less than an hour, and it was easy, breezy, beautiful, Raspberry Pi.


I soldered ten lasers in parallel and connected ten photoresistors to their own GPIO pins. I didn’t wire them up in series because of sensitivity reasons and to make debugging easier.

Building the frame took a few tries: I actually started with a wood frame, then tried a clear case, and finally realized the best and cleaner solution would be pipes. All the wires go inside the pipes and come out in a small window on the top to wire up to the Zero W.



Using pipes also made the build cheaper, since they were about $3 for 12 ft. Wiring inside the pipes was tricky, and to finish the circuit, I soldered some of the wires after they were already in the pipes.

I tried glueing the lasers to the frame, but the lasers melted the glue and became decalibrated. Next I tried tape, and then I found picture mounting putty. The putty worked perfectly — it was easy to mold a putty base for the lasers and to calibrate and re-calibrate them if needed. Moreover, the lasers stayed in place no matter how hot they got.

Estefannie Explains It All Raspberry Pi Cookie Jar

Although the lasers were not very strong, I still strained my eyes after long hours of calibrating — hence the sunglasses! Working indoors with lasers, sunglasses, and code was weird. But now I can say I’ve done that…in my kitchen.

Using all the knowledge I have shared, this project should take a couple of hours. The code you need lives on my GitHub!

Estefannie Explains It All Raspberry Pi Cookie Jar

“The cookie recipe is my grandma’s, and I am not allowed to share it.”

Estefannie on YouTube

Estefannie made this video for us as a gift, and we’re so grateful for the time and effort she put into it! If you enjoyed it and would like to also show your gratitude, subscribe to her channel on YouTube and follow her on Instagram and Twitter. And if you make something similar, or build anything with our free resources, make sure to share it with us in the comments below or via our social media channels.

The post Laser Cookies: a YouTube collaboration appeared first on Raspberry Pi.

Help us translate our YouTube videos

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/youtube-translations/

As we work to create more content for our YouTube channel, making our videos as accessible as possible is key to serving the growing Raspberry Pi community. And as we push to create more videos linked to our collection of free resources, providing translated subtitles will help to bring our content to more people across the globe.

We need your help to make this happen.

YouTube translations Raspberry Pi

Subtitles for our ‘Getting started with soldering‘ video translated into Portuguese.

Translating YouTube

We recently enabled translation submissions for all our YouTube content, allowing viewers, subscribers, and members of the community to contribute translated subtitles, descriptions, and titles for all of our videos.

YouTube Subtitle translations Raspberry Pi

Once approved, these translated subtitles are available for all viewers of our videos via the closed captioning button on the navigation bar of every video, while translated descriptions and titles will automatically be shown, based on your location. Anyone who has contributed to the translations is automatically credited in the video’s description.

YouTube translations Raspberry Pi

Thanks Mário!

Our aim is to collect translations of our videos in as many languages as possible, including the original English. While YouTube does a great job of using speech-to-text to create automatic subtitles, these aren’t always correct – especially when the videos feature loud background noises and music – so we need to create subtitles in English too.

Submit your own YouTube translations

If you’d like to contribute subtitles for our YouTube videos, you can do so by heading to the Community Contributions page for our channel. Simply pick a video you’d like to translate and work your way through. The system is very easy to navigate and allows you to manage the timing of subtitles, which is very handy. Once complete, your translation will be sent to us to double check. When we’ve approved it, it will be published. If we find any issues with the translation, we’ll let you know via the Community Contributions page.

YouTube translations Raspberry Pi

A sneaky peak into what we see on the other side

If you find a video that’s already been translated, but you see faults in the language and/or grammar used, you can also correct and improve existing translations.

Thank you

If you contribute a translation to any of our videos, make sure you post a comment for the world to see in the video’s comments section. If you have a Twitter account, leave your username in the comment and we’ll make sure to thank you on the official Raspberry Pi account when we’ve approved your submission.

Thank you to everyone who has contributed so far, and to everyone who is now logging into YouTube to take part. It’s things like this that make our community the best out there.

Thank you.

The post Help us translate our YouTube videos appeared first on Raspberry Pi.

Sean’s DIY Bitcoin Lottery with a Raspberry Pi

Post Syndicated from Alex Bate original https://www.raspberrypi.org/blog/seans-diy-bitcoin-lottery/

After several explorations into the world of 3D printing, and fresh off the back of his $5 fidget spinner crowd funding campaign, Sean Hodgins brings us his latest project: a DIY Bitcoin Lottery!

DIY Bitcoin Lottery with a Raspberry Pi

Build your own lottery! Thingiverse Files: https://www.thingiverse.com/thing:2494568 Pi How-to: http://www.idlehandsproject.com/raspberry-pi-bitcoin-lottery/ Instructables: https://www.instructables.com/id/DIY-Bitcoin-Lottery-With-Raspberry-Pi/ Send me bitcoins if you want!

What is Bitcoin mining?

According to the internet, Bitcoin mining is:

[A] record-keeping service. Miners keep the blockchain consistent, complete, and unalterable by repeatedly verifying and collecting newly broadcast transactions into a new group of transactions called a block. Each block contains a cryptographic hash of the previous block, using the SHA-256 hashing algorithm, which links it to the previous block, thus giving the blockchain its name.

If that makes no sense to you, welcome to the club. So here’s a handy video which explains it better.

What is Bitcoin Mining?

For more information: https://www.bitcoinmining.com and https://www.weusecoins.com What is Bitcoin Mining? Have you ever wondered how Bitcoin is generated? This short video is an animated introduction to Bitcoin Mining. Credits: Voice – Chris Rice (www.ricevoice.com) Motion Graphics – Fabian Rühle (www.fabianruehle.de) Music/Sound Design – Christian Barth (www.akkord-arbeiter.de) Andrew Mottl (www.andrewmottl.com)

Okay, now I get it.

I swear.

Sean’s Bitcoin Lottery

As a retired Bitcoin miner, Sean understands how the system works and what is required for mining. And since news sources report that Bitcoin is currently valued at around $4000, Sean decided to use a Raspberry Pi to bring to life an idea he’d been thinking about for a little while.

Sean Hodgins Raspberry Pi Bitcoin Lottery

He fitted the Raspberry Pi into a 3D-printed body, together with a small fan, a strip of NeoPixels, and a Block Eruptor ASIC which is the dedicated mining hardware. The Pi runs a Python script compatible with CGMiner, a mining software that needs far more explanation than I can offer in this short blog post.

The Neopixels take the first 6 characters of the 64-character-long number of the current block, and interpret it as a hex colour code. In this way, the block’s data is converted into colour, which, when you think about it, is kind of beautiful.

The device moves on to trying to solve a new block every 20 minutes. When it does, the NeoPixel LEDs play a flashing ‘Win’ or ‘Lose’ animation to let you know whether you were the one to solve the previous block.

Sean Hodgins Raspberry Pi Bitcoin Lottery

Lottery results

Sean has done the maths to calculate the power consumption of the device. He says that the annual cost of running his Bitcoin Lottery is roughly what you would pay for two lottery scratch cards. Now, the odds of solving a block are much lower than those of buying a winning scratch card. However, since the mining device moves on to a new block every 20 minutes, the odds of being a winner with Bitcoin using Sean’s build are actually better than those of winning the lottery.

Sean Hodgins Raspberry Pi Bitcoin Lottery

MATHS!

But even if you don’t win, Sean’s project is a fun experiment in Bitcoin mining and creating colour through code. And if you want to make your own, you can download the 3D-files here, find the code here, and view the step-by-step guide here on Instructables.

Good luck and happy mining!

The post Sean’s DIY Bitcoin Lottery with a Raspberry Pi appeared first on Raspberry Pi.